Tag Archives: SBC

RedBear BLE Module

Bluetooth Low Energy (BLE) transceiver board. BLE is a new protocol introduced in the 4.0 revision of the Bluetooth standard. It is a wireless personal area network (PAN) technology aimed at novel applications in the healthcare, fitness, security, and home entertainment industries.  BLE is not backward-compatible with the previous Bluetooth protocol. However it uses the same 2.4 GHz frequency bands but a simpler modulation scheme. The picture below shows the RedBearLab BLE Mini Board.MKRBL2-2T

The module is a combo of a RBT01 BLE module featuring the Ti CC2540 Single chip Bluetooth (SoC) and a breakout board that offers a micro USB connector and a 3.3Volt UART connectors. The main reason this board caught my attention is the fact that it also has solder points for additional GPIOs on the back of the board. These GPIOs can be custom programed. So it should be possible to hook up  I2C or SPI sensors to the board and with a bit of software be able to monitor them.
Using such a BLE board  is not exactly an IoT solution as the connectivity to the cloud would have to be implemented with for example a Wireless enhanced Gallileo. Also the BLE's range is rather limited. However when it comes to power consumption BLE has a leg up as it was specifically designed for very low power.

Spark Core Weather Station

In my previous blog post I described my first encounter with the Spark Core. Today I want to demonstrate a first simple code example. For this I connected the Spark Core to a Weather Shield from Sparkfun. The shield offers sensors for light, humidity, temperature and pressure. It can even be extended with rain and wind sensors as well as GPS.
.Spark Core Weather
The shield comes with a nice set of libraries and examples that I used as a starting point. To keep things really simple, I combine the entire Weather Shield source with the sensor library functions and the setup() and loop() into a single file. This did not take long and compiled quickly. I also removed the wind and rain related functionality as I did not plan to use those. The source code below takes measurements every second and writes the them to the USB serial port.

For debugging I used the Serial Communication link over USB. Windows users have to install a COM driver. However, MAC and Linux support the Spark Core USB functionality out of the box.

I was really pleased to see how well the Spark Core supports Arduino libraries and well written legacy code. With only a few code modifications I had the sensors up and running.

The setup is now streaming values over a USB cable to a PC. There I captured the values with Tera Term and created a Weather Graph from the comma separated values (CVS). The example below shows the pressure curve of a Bay Area Storm passing by at end of February 2014.
CA Storm
This setup is a somewhat trivial example that a basic Arduino can also do. The project really does not take advantage of the Spak Core's connectivity to the internet. So stay tuned for my next blog post where I will add internet connectivity to the setup.

Encounter with a Spark

I have tested several IoT platforms over the last couple of weeks. So I was not too keen to checkout yet another one. However, when I got the annoucement that the Spark Core is shipping I could not resist and ordered one. It arrive in the mail today so I thought I will take it for a spin.

The Spark Core comes in a very stylish little box.

Spark Box

Figure1: Spark Box

To my surprise the box did even includes a breadboard:

spark2spark3

Figure 2: Open Spark Core Box

Overall, the box contains the Spark Core board, a breadboard, a micro-USB cable and Spark sticker.

spark4

Figure 3: Box Content

It is amazingly simple to get the board up and running. By following these few simple steps:

  1. Download the Spark App for iPhone or Android
  2. Setup an account by register at spark.io
  3. Power up the Spark Core over the USB cable
  4. Start Spark App and log into your wireless network

If everything works well you will get rewarded with the RGB-LED on the Spark board flashing in rainbow colors. Once the Spark Core is connected to you WiFi and paired with the Spark cloud, it took me only a few minutes to get an on-board blue LED blinking.

It very quickly becomes obvious that the Spark team has done a great job setting up an entire end-to-end IoT solution consisting of:

  1. Spark Hardware
  2. Cloud based IDE
  3. Arduino compatible API
  4. Free for life cloud back-end service with a RESTful API

All the Spark Core software is open source. The board uses a CC3000 WiFi Module from TI combined with a 32-bit ARM Cortex-M3 powered STM32F103 from ST Microelectronics. The Spark team has come up with a nice integration of this hardware and the cloud server back end. It is based on the CoAP protocol specification and allows for an easy and energy efficient integrated IoT solution.

The cloud API offers over-the-air (OTA) firmware updating where the input can either be c/c++ source code or binaries. For those that don't want to use Spark Builder, their cloud based IDE the web site also promises support for desktop IDEs like Eclipse.

So much for today, I will cover more details in future blogs.

How does Galileo Stack up against Raspberry PI

I am interested is to compare Galileo and other DIY single board computers. In this post I want to analyze the Galileo board against the popular Rasberry PI. The first thing to note is that the Rasberry PI is not an Arduino compatible platform. However, there are now extension boards available that allow to use Arduino shields with Raspberry PI. Here are to examples: The first is the AlaMode for Raspberry Pi  the second is the GertDuino: Add-On Board for Raspberry PI . Both boards are priced in the range of a Rasberry PI. So the combination of a Raspberry PI with an Arduino shield extension puts this solution right where the Galileo board is.

Have a look at the table below. It compares the two single board computer's hardware. The technical data for the Raspberry PI are taken from WikiPedia.

Rasberry PI Model A Rasberry PI Model B Intel Galileo
Target price: US$ 25 US$ 35 US$69
SoC: Broadcom BCM2835 (CPU, GPU, DSP, SDRAM, and single USB port) Intel Quark X1000
CPU: 700 MHz ARM1176JZF-S CPU 400MHz 32-bit x86 Pentium Class CPU
GPU: Broadcom VideoCore IV @ 250 MHz none
Memory (DRAM): 256 MBytes (shared with GPU) 512 MBytes (shared with GPU) as of 15 October 2012 256 Mbyte
PCIe ports: none PCIe 2.0
USB 2.0 ports: 1 Host 2 Host (from LAN9512) 1 Host,
2 Device
Video input: A CSI input connector allows for the connection of a RPF designed camera module none
Video outputs: Composite RCA (PAL and NTSC), HDMI (rev 1.3 & 1.4), raw LCD Panels via DSI none
Audio outputs: 3.5 mm jack, HDMI, and, as of revision 2 boards, I²S audionull none
Onboard storage: SD/MMC/SDIO 3.3V card slot SD/MMC/SDIO 3.3V card slot
Onboard network: None 10/100 Ethernet (from LAN9512) 10/100 Ethernet
Low-level peripherals: 8 × GPIO, UART, I²C bus, SPI bus with two chip selects, I²S audio +3.3 V, +5 V, ground 16 × GPIO,
UART, I²C bus, SPI
Power ratings: 300 mA (1.5 W) 700 mA (3.5 W) 550 mA (1.9-2.2W)
Power source: 5 volt via MicroUSB or GPIO header 5 Volt
Size: 85.60 mm × 53.98 mm (3.370 in × 2.125 in) 106.68 mm x 71.12 mm (4.2 in x 2.8 in)

The Raspberry PI uses a SoC chip that was originally designed for the set-top box market. Therefore it shows a nice lineup of features on the video side. The integrated HDMI port and on-chip graphics accelerator are testimony to this. However for IoT applications the Quark X1000 SoC used by Galileo offers a really nice selection of interfaces.

Is Edison competing with Galileo

Last summer at the Maker Fair in Rome Intel announced the Galileo single board computer . This week at CES 2014 in Las Vegas Intel followed up with another initiative that carries an inventors name. This time it is Edison. The Edison board is more advanced take on the Quark System on a Chip (SoC) based single board. The board is only the size of an industry standard SD card. So don't expect to solder it yourself.

edison

However the card is a full featured single board computer that will offer support for multiple operating systems (OS).  The integrated WiFi will turn any device equipped with an Edison into an IoT solution.

Intel also promised to release design files that will make it easy to  integrate Edison into your own project.  Among the tool vendors that will support Edison is Autodesk. The company just announced the  acquisition of circuit.io. This online PCB design tool is now a part of Autodesk's 123D design suite.

For those that cannot wait and want something today the Electric Imp Wireless SD-CARD is an interesting alternative. This card is clearly not as powerful as an Edison. However given the creativity that innovators have displayed around the meager Arduino 8-bit AVR CPU  it may still be plenty.

El_Imp